|
|
Post by AJR on Jun 11, 2017 8:00:28 GMT -7
Since the in line stock rules only have specific bans for braid and shunts, is it safe to assume that threaded brush barrels are permitted? Domt wanna be like Smokey Yunick and say "they didn't say you couldn't". Bill we are running as per the NTRA Stock Inline rules. They say stock and aftermarket electrical parts are allowed. I just reposted the no braids and shunts and no silli foams as a reminder, but they are in the rules as well. The only "House Rules" are the 22g minimum weight and the 20v they will run at. NTRA rules nitroslots.com/page/ntra-rules |
|
|
|
Post by ecbill on Jun 11, 2017 11:40:34 GMT -7
When asking the question, I was quoting directly from the NTRA rules.
Stock & After
market parts allowed
No shunts or braids
Wasn't sure if threaderd barrels falls under aftermarket parts or not. Just looking for clarification. Either way, I'll abide by the rules.
|
|
|
|
Post by AJR on Jun 11, 2017 15:59:49 GMT -7
When asking the question, I was quoting directly from the NTRA rules. Stock & After market parts allowed No shunts or braids Wasn't sure if threaderd barrels falls under aftermarket parts or not. Just looking for clarification. Either way, I'll abide by the rules. Yep......you're good either way. Run'em. |
|
|
|
Post by ecbill on Jun 12, 2017 2:07:01 GMT -7
That's good news! I've been launching brushes and springs all over the room, trying to install them the conventional way. Most of them, never to be found again.
Thanks for the clarification.
|
|
|
|
Post by dave632 on Jun 12, 2017 9:24:16 GMT -7
I think I launched a few parts to the moon in the past. Now classified as space junk..
|
|
|
|
Post by kdog on Jun 12, 2017 10:00:09 GMT -7
Brush Springs just want to be FREE !That's good news! I've been launching brushes and springs all over the room, trying to install them the conventional way. Most of them, never to be found again. Thanks for the clarification.
|
|
|
|
Post by woodcote on Jun 13, 2017 0:14:33 GMT -7
My cars are on their way across the Pond... a Mustang Funny Car for the Kiwi Challenge, plus two Fords (an Escort and a Capri) for the inline stock manufacturers race. No PSO shark pool car this time (needs more work), so there was room in the box for that second Ford.
|
|
|
|
Post by ecbill on Jun 13, 2017 2:14:58 GMT -7
Now that I've got the green light, I'm all out of brushes. The tubes I was going to use are in a G+ chassis. Closer inspection showed that they are soldered in place. Think its gonna have to go racing as is this time.
|
|
|
|
Post by AJR on Jun 13, 2017 5:45:51 GMT -7
My cars are on their way across the Pond... a Mustang Funny Car for the Kiwi Challenge, plus two Fords (an Escort and a Capri) for the inline stock manufacturers race. No PSO shark pool car this time (needs more work), so there was room in the box for that second Ford. Andy I will be looking for them. Lists have been updated. |
|
|
|
Post by dave632 on Jun 13, 2017 10:33:57 GMT -7
All my cars have left for Texas. Should be there in a few days.
|
|
|
|
Post by AJR on Jun 14, 2017 17:45:43 GMT -7
All my cars have left for Texas. Should be there in a few days. Dave your cars arrived today. All have been checked and are sitting in the pits waiting for raceday. |
|
|
|
Post by dave632 on Jun 14, 2017 18:16:02 GMT -7
Already, got to tell the driver to slow down, must have kept the pedal to the metal the whole way!!
In a hurry to race I guess..
|
|
|
|
Post by hairycanary on Jun 14, 2017 22:18:11 GMT -7
Jeff could you please add one more Chrysler to the Manufactures Challenge. I'm also working on a PSO car but I'm running out of time. If I get it done in time it will be only primered. Work in progress.
Thanks Rick
|
|
|
|
Post by AJR on Jun 15, 2017 2:58:46 GMT -7
Rick I have added another Chrysler for you. Primer is good......."paint don't make it fast!" Thanks for being a part of the race.
|
|
|
|
Post by dave632 on Jun 15, 2017 7:33:55 GMT -7
|
|
