Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Oct 7, 2020 20:16:50 GMT -7
Thank You Dave
|
|
|
|
Post by dave632 on Oct 8, 2020 8:28:04 GMT -7
You are welcome Al.
I have found such a wide variety of gauss range with ceramic magnets that I rarely worry about magnets
when I am tuning a car. The difference magnets make, that I have found, is in the 60' & 330' times. There better magnets
usually make some difference if the car has the traction to take advantage of it. Many cars, I have found, will start yanking
the front end off the ground, even with wheelie bars, and causing the ET to be worse because of poor rail contact. Therefore
there is usually a compromise between stronger and weaker motor magnets there as well as matching them to the arm. I have
killed the performance of some cars when trying even Poly motor magnets in some of them.
The Neo motor magnets are useless in all but sub 1 ohm Unlimiteds. The yellow dragster I recently sent to Jeff's race had
Poly magnets in it and it had a sub 1 ohm arm in it. I know it would have been slower if I put Neos in it as that chassis
could not have handled it.
|
|
|
|
Post by ecbill on Oct 8, 2020 11:16:13 GMT -7
This notice is for everyone running the Street Outlaw list race.
3GO voltage has been increased to 20 volts.
This is a permanent change so please test your cars at this voltage. Don’t know how many times I forgot to switch back to 18v during testing. Thanks! |
|
|
|
Post by dave632 on Oct 8, 2020 14:24:06 GMT -7
Yes Bill, that's one of the main reasons I voted for the switch. I have done the same thing countless times.
The slight increase in speed and ET should not effect anyone's tune very much. Make sure your wheelie bar is
not set too high as the cars may yank the guide pin out of the slot even with the bars. I set mine at about .020
or about a fingernail width.
|
|
|
|
Post by skillet on Oct 8, 2020 15:15:18 GMT -7
Thanks for telling us about your track Dave. I just realized how important that is. I have some tyco track wich the rail is slightly higher than afx. With that rail being slightly higher im thinking I may need a touch bigger front tire to keep the flow of my car going for the different track. Skillet
|
|
|
|
Post by dave632 on Oct 8, 2020 20:05:23 GMT -7
If I remember right the rail height on the Max Track is .013-.014. which is higher than AFX or Tyco.
|
|
|
|
Post by nosubfor3 on Oct 9, 2020 16:05:33 GMT -7
Dave put me in for 2 each of the 1.0, Inline SS and Pro Mod. Blue Silk and Purple Haze will be there also. Put them in any spot on the list that is appropriate.
|
|
|
|
Post by dave632 on Oct 9, 2020 18:07:06 GMT -7
Welcome to the race Nosubfor3 and good luck.
|
|
|
|
Post by hairycanary on Oct 9, 2020 18:31:25 GMT -7
Dave can you please put me down for 2 in each class and a Inline unlimited please. This will be my first attempt at a Inline unlimited should be fun ? Thanks for hosting the race !
Rick
|
|
|
|
Post by dave632 on Oct 10, 2020 7:16:20 GMT -7
Welcome to the race Hairy Canary and good luck. Congrats on taking on Unlimited, you will find new challenges there.
|
|
|
|
Post by GTS on Oct 15, 2020 16:43:31 GMT -7
Dave, thanks for putting on the race and please sign me up for: 2 @ Index 1.0 1 @ Inline SS 1 @ Inline Pro Mod
Thanks!
|
|
|
|
Post by dave632 on Oct 15, 2020 17:04:50 GMT -7
Welcome to the race GTS and good luck.
|
|
|
|
Post by GTS on Oct 18, 2020 16:40:37 GMT -7
Hiya Dave, will you sign me up for 1 more in the Inline Pro Mod class, for a total of 2. Thank you!
|
|
|
|
Post by dave632 on Oct 18, 2020 17:27:22 GMT -7
Will do Gale.
|
|
|
|
Post by bluesguy on Oct 23, 2020 18:15:36 GMT -7
Hey Dave, can you put me down for 1 inline s/s, 1 pro mod 2.5, 1 shark pool for 3 gear, 1 sharkpool for 4 gear. I read that inline s/s no longer allows timing changes on the super G+ chassis.
Also the street oulaws 3 gear is now 20v, what voltage on 4 gear? Looking forward to this race, been a while for me, quess I got some catching up to do.
Thanks,
Mike Marvin
|
|
