|
|
Post by AJR on Jun 24, 2022 18:14:19 GMT -7
Plus, found a box stock AW 4G that did 1.006 out of the box. May be some potential there. I had one of those, but with a little work i was able to slow it down. That's funny Mike   |
|
|
|
Post by skillet on Jun 24, 2022 18:42:31 GMT -7
Hey Bill they are like tyco 440x2. Tyco and wizzard parts will fit the thunder cat even the brush barrels. Comes down to magnets ,chassis ,and shoes really that dont change out.
I dont know if the body clip works. I did take a extra body clip from a autoworld super lll and cut the tabs off and glued them in a body to fit....give me a second and ill get a picture
|
|
|
|
Post by skillet on Jun 24, 2022 19:12:50 GMT -7
|
|
|
|
Post by ecbill on Jun 24, 2022 20:25:07 GMT -7
Let's see a picture. What's the name of the replacement chassie you got I probably have ceramic magnets for it. Here are some pics  D6B6DB12-84ED-41BD-91E4-AF030AABB53F by Bill Le, on Flickr one on left has smaller motor mags but slightly larger traction mags. Don’t know the model name. Bought it from Jag. I’ll have to look it up and hope he only sells one type.  C072E6DC-0586-4D56-9865-115068CA2689 by Bill Le, on Flickr The one on the right I bought from some joker on eBay. Looked fairly new but rear axle “holes” are worn so bad that when you hit the gas the rear axle pops out, like the cop on American Graffiti. Even tried a .063 axle. Looked it up on Jag’ site. He shows it as a WS12 with no name. Looked up WS12 on Wiz site, and it appears to be a Storm or Storm extreme. No clue on car on right. |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jun 24, 2022 20:36:51 GMT -7
most racers drill a hole under where the axle fits through the holes for retainer pins.
so, the retainer pins go from the back of the chassis, under the axle and into the chassis just in front of the axle.
I cannot ID those.
|
|
|
|
Post by ecbill on Jun 24, 2022 20:43:12 GMT -7
most racers drill a hole under where the axle fits through the holes for retainer pins. so, the retainer pins go from the back of the chassis, under the axle and into the chassis just in front of the axle. I cannot ID those. Good idea. Why didn’t I think of that?  |
|
|
|
Post by skillet on Jun 24, 2022 20:55:50 GMT -7
The one without magnets is a storm. The other one may be a patriot1.
I think the patriot 2 and 3 are diffrent in the front
|
|
|
|
Post by skillet on Jun 24, 2022 20:59:40 GMT -7
Heres a storm and a patriot 3. The patriot is the chassis not put together.  |
|
|
|
Post by Eagle Racing on Jun 25, 2022 4:56:02 GMT -7
I don't remember the last time I raced in a Nitro Slots race, been along time. New track new race master, and he likes drag bikes. So I said to myself this should be fun. Here are my entries: Tyco Motorcycle, Eagle Motorcycle, Dodge Neon with Viper setup for inline, and my little red Mustang with an Eagle Chassis and N20 motor for inline. The Mustang and Neon are running almost the same times on my black plastic track. However if it freaks you out or others complain then don't run it. I would like to at least see what it does on your track.
The white Eagle Motorcycle is for Ty Powers, Sam. That is his entry for match race. The rider is not glued down so will have to run bike rider less. It is that way so he can paint it.
|
|
|
|
Post by skillet on Jun 25, 2022 12:12:28 GMT -7
Sounds good to me Robert. Cant wait to see them myself.
|
|
|
|
Post by Eagle Racing on Jun 25, 2022 17:56:52 GMT -7
Sounds good to me Robert. Cant wait to see them myself. Thanks Sam, looking forward to racing on your track. It should be a blast! |
|
|
|
Post by skillet on Jun 26, 2022 2:00:49 GMT -7
Should be alot of fun. Didnt get to respond earlier was working. Copy that on Ty's bike. Al is in also, im not sure if ill make it a seperate race or run it as a grudge match show down in between the race. Either way its going to be exciting.
I like grudge match/ call out racing so hopefully will see you here more often.
I dont see a can motor breaking the rules. The magnets and arms fall in spec. I know they are harder to tech but we are open to everything except neo in the in-line class. Shouldn't be an issue.
|
|
|
|
Post by skillet on Jun 26, 2022 2:04:58 GMT -7
Racers in the house
Fin - Ty - Dyno - Mazda - AlPink - Comet - Cross - Vinnie - Cricket - CarLa60 - Gnome
|
|
|
|
Post by skillet on Jun 26, 2022 2:42:01 GMT -7
Track up date = We now have win lights over each lane at the finish. Winner lane lights up. This will help with some of the grudge match racing we may want the ET to stay hidden.  |
|
|
|
Post by mazda on Jun 26, 2022 4:17:47 GMT -7
The track is looking really great Sam. I am looking forward to racing on it. What tyres do you guys use on the Tyco motorcycles? I have two but I didn’t have time to get one ready for the race.  |
|
this next one is the tyco narrow body it accepts. 
